Product Description

If you have compressor inquiry please tell us follows information when you send inquiry:
*Compressor working medium: If single gas ,how many purity ? if mixed gas , what’s gas content lit ?
*Suction pressure(gauge pressure):_____barg
*Exhaust pressure(gauge pressure):_____barg
*Flow rate per hour for compressor: _____Nm³/h
Compressor gas suction temperature:_____ºC
Compressor working hours per day :_____hours
Compressor working site altitude :_____m
Environment temperature : _____ºC
Has cooling water in the site or not ?______
Voltage and frequency for 3 phase :____________
Do not has water vapor or H2S in the gas ?______
Application for compressor?__________

Oil free Sulfur Hexafluoride Compresor SF6 Technial Parameters
 

Model Flow Rate Nm3/h Inlet Pressure
MPa
Discharge Pressure
MPa
Rated Power
KW
Inlet Port
Dia
Outlet Port
Dia
Dimension
(L*W*H)mm
VWZ-10/6-45 10 0.6 4.5 4 M36*2 M36X2 1000*600*750
VWZ-20/6-45 20 0.6 4.5 5.5 M36*2 M36X2 1000*600*750
WWZ-30/6-45 30 0.6 4.5 7.5 M36*2 M36X2 1100*640*870
WWZ-40/6-45 40 0.6 4.5 11 M36**2 M36X2 1200*700*870
WWZ-60/6-45 60 0.6 4.5 15 M36*2 M36X2 1200*730*870
WWZ-80/6-45 80 0.6 4.5 18.5 M36*2 M36X2 1300*760*870

SF6 Sulfur Hexafluoride Compressor Features:
SF6 gas booster compressor was designed 100% oil-free. Its CZPT ring, piston ring using self-lubricating materials, bearing parts using high-temperature grease lubrication, to avoid the compression process of gas pollution, ensure the purity of gas no any contacts.

Its shaft head seal is sealed by rotating magnetic fluid seal. Highly Effective prevent the leakage of sulfur hexafluoride gas, reduce gas loss, ensure the safety and CZPT of operators, and avoid environmental pollution caused by toxic substances.

  1. 100% Oil-free Lubrication, the gas is clean, high purity, and non-polluting.
  2. High efficiency and low energy consumption.
  3. Fully balanced design, low vibration.
  4. High reliability, continuous operations
  5. No special basic requirements, easy to install for use and maintenance.
  6. Air-cooled or water-cooled can be chosen, to reduce installation cost.
  7. Compact structure, low operating and maintenance cost.

Application of SF6 Gas Compressor (Sulfur Hexafluoride Compressor):
This series compressor is suitable for recovering sulfur hexafluoride gas.
Suction pressure: can be minus pressure from -0.05Mpag to -.6Mpa(G)  (-0.05) ~ 0.6Mpa (G), Discharge pressure: can reach to 5.0Mpa (G)
SF6 gas can be highly efficient recycling by CZPT SF6 recycling booster compressor.
And it also mainly used in the repair and maintenance of SF4 circuit breakers, recycling SR Gas in the circuit breaker.

The advantages  & usages of sulfur hexafluoride gas 

1. As a refrigerant in the refrigeration industry, the refrigeration range can be between -45°C and 0°C.

2.  The electrical industry uses its high dielectric strength and good arc extinguishing performance as an insulating material for high-voltage switches, large-capacity transformers, high-voltage cables and gases. Sulfur hexafluoride is widely used in the electrical industry for its good insulating properties and arc extinguishing properties, such as circuit breakers, high-voltage switches, high-voltage transformers, gas-enclosed combined capacitors, high-voltage transmission lines, transformers, etc. Gas insulators for electronic equipment, radar waveguides, particle accelerators, transformers, arresters, etc.

3. It is used as a desorbent in the mining industry to replace oxygen in coal dust in mines.

4. Play role as a tracer. Because sulfur hexafluoride is highly sensitive, non-toxic, stable in performance, reliable in inspection methods, and has very little content in nature, it is often used as a tracer in the environmental protection industry. For air pollution monitoring and hydrogeological research. As a widely used tracer for the determination of air pollution, sulfur hexafluoride has a tracer distance of up to 100 kilometers.

5. Electronic grade sulfur hexafluoride (SF6) is suitable for cleaning and etching processes in TFT-LCD panel factories and semiconductor factories and can be used as a single-film fiber isolation layer dopant in the manufacturing process of optical fibers. Electronic grade high-purity sulfur hexafluoride is an ideal electronic etchant and is widely used in the field of microelectronics technology.

6. SF6 is also widely used in metal smelting (such as magnesium alloy melting CZPT protective gas), aerospace, medical (X-ray machine, laser machine), meteorology ( Tracer analysis), chemical industry (advanced car tires, new fire extinguishers), etc. In the smelting and casting process of non-ferrous metals, sulfur hexafluoride can prevent the oxidation of magnesium and its alloy melts, and can also be used for degassing and purification of aluminum and its alloy melts.

7. In the pharmaceutical industry, the most advanced contrast agent ultrasound method CnTI currently uses sulfur hexafluoride as the contrast agent. The other name called SonoVue (SonoVue), can diagnose, and is said to increase the screw pressure, so as to provide full power independent of diving depth.

8. Inflate pure gaseous sulfur hexafluoride into the finished sports ball inner tube to reach a usable air pressure. The inner tube pressure of the sports ball will remain stable for a long time. The sports ball can be used for a long time without the need for a second inflation to supplement the air pressure.

9.  Standard gas, leak detection gas, carrier gas of chromatograph.

The Oil free Oxygen piston booster compressor is widely used in oxygen industry such as air separation oxygen plant and medical industry.

Technical Paramter of Oil Free Piston Oxygen Gas Booster Compressor

Model Flow rate Suction Pressure Discharge Pressure Motor Power Dimension Interface diameter
Nm3/h MPa MPa KW mm×mm×mm  
ZWZ-5/1.5-10 5 0.15 1 1.5 1000×500×700 Rc 1/2′
VWZ-10/1.5-10 10 0.15 1 2.2 1000×500×700 Rc 1′
VWZ-15/1.5-10 15 0.15 1 3 1000×500×700 Rc 1′
WWZ-20/1.5-10 20 0.15 1 4 1200×650×800 Rc 1′
WWZ-25/1.5-10 25 0.15 1 5.5 1200×650×800 Rc 1′
WWZ-30/1.5-10 30 0.15 1 5.5 1200×650×800 Rc 1′
WWZ-50/1.5-10 50 0.15 1 7.5 1200×650×800 Rc 1′
ZWZ-5/4-14 5 0.4 1.4 1.5 1000×500×700 Rc 1/2′
ZWZ-10/4-14 10 0.4 1.4 2.2 1000×500×700 Rc 1′
ZWZ-15/4-14 15 0.4 1.4 2.2 1000×500×700 Rc 1′
VWZ-20/4-14 20 0.4 1.4 3 1200×650×800 Rc 1′
VWZ-25/4-14 25 0.4 1.4 4 1200×650×800 Rc 1′
VWZ-30/4-14 30 0.4 1.4 5.5 1200×650×800 Rc 1′
WWZ-50/4-14 50 0.4 1.4 7.5 1200×650×800 Rc 1′

All standard cylinder oxygen filling diaphragm compressor are CE marked to meet the requirements of the EU market. We can also provide customized plant filling oxygen compressor according to customer conditions. Our microboost medical oxygen compressor have the following features According to the different working conditions of the customer:
1. Completely 100% oil free, no oil required (depending on the specific model)
2. Oxygen for  PSA Oxygen Generator
3. NO pollution, keep the same purity into the gas
4. RELIABLE and high quality, comparable to the American RIX brand.
5. TOP low cost, low maintenance cost, simple operation, just change the piston ring
6. 4000 hours piston ring working life under low pressure conditions, 1000-2000 hours working life under high pressure conditions
7. High quality high efficient brand motor, can be customized for high sea level use with more long service life.
8. CE approved to meet the requirements of the EU market
9. According to the customer’s specific working conditions, the compressor is designed for single machine compression, two-stage compression, three-stage compression and four-stage compression.
10. Low speed, long life, average speed 360-760RPM,
11. Low noise, average noise below 75dB, can work quietly in the medical field
12. Each stage has an interstage safety valve. If the stage is overpressured, the safety valve will take off and release the overpressure gas to ensure the stable operation of the compressor.
13. Each level has a temperature controller. If the temperature between the stages exceeds the standard, the temperature display will sound and light alarm.

Oil free Process Gas Piston Compressor

TOTALLY OIL FREE HIGH PRESSURE RECIPROCATING PISTON COMPRESSOR 
Description of Advantages of Oil-free Piston Compressor 
1) Totally 100% oil free type gas compressor, cylinder no need oil lubrication, ensure cylinder 100% no oil content.
2) Suitable compressing for Oxygen gas, Hydrogen gas, Nitrogen gas, Helium gas, Argon gas, CO2 gas, Air gas, Biogas, Methane gas and other special gas 
3) No pollution, keep same purity to inlet gas
4) Reliable and top quality, comparable with USA RIX brand.
5) Top cost performance, low maintenance cost, and easy operation, only need to change piston ring
6) 4000 hours piston ring working life,1500-2000 hours working life for final stage ring 7
7) Top brand motor, and can be specially pointed, like Simense brand
8) Supply Japan market, quality approval by Japan strictly system
9) CE approval
10) The gas compressor carefully designed and manufactured for 2Mpa, 4Mpa,10Mpa, 15Mpa, 20MPa-30MPa pressure etc.
11)  The device has a small size, lightweight, easy maintenance, and friendly at moving and operating.
12) Output gas non-toxic, odorless. Suitable for filling high-pressure air displacement and small and medium-sized gas station
Model
SF6 COMPRESSOR

Power(Hp,Kw):   3KW-110KW

Working Pressure(Bar,Psi):    150/200/250/300bar/350bar

Air Delivery(L/min,CFM):   5/10/15/20/25/30/35/40/50/60/100 Nm3/Hr

Inlet pressure ,outlet pressure:  0.2-0.4Mpa, 10Mpa/15Mpa/20Mpa/23Mpa/30Mpa

Speed(r.p.m):   200-400

pressure stage:   3-4-5barg

Net Weight(Kgs): 1200

Cooling way:   Air cooling/water cooling
 

150bar  Oil-Free Piston Type Oxygen Booster Compressor Technical Parameters Table
Model Flow rate Suction Pressure Discharge Pressure Motor Power Inlet Interface diameter Outlet Interface diameter Dimension
Nm3/h MPa MPa KW mm×mm×mm
WWZ-5/4-150 5 0.4 15 4 DN20 M14×1.5 1080×820×850
WWZ-8/4-150 8 0.4 15 5.5 DN20 M14×1.5 1080×820×850
WWZ-10/4-150 10 0.4 15 7.5 DN20 M14×1.5 1080×870×850
WWZ-12/4-150 12 0.4 15 7.5 DN20 M14×1.5 1080×870×850
WWZ-15/4-150 15 0.4 15 11 DN20 M14×1.5 1150×970×850
WWZ-20/4-150 20 0.4 15 15 DN20 M14×1.5 1150×970×850
WWZ-25/4-150 15 0.4 15 11 DN20 M14×1.5 1150×970×850
WWZ-30/4-150 20 0.4 15 15 DN20 M14×1.5 1150×970×850
WWZ-25/4-150 25 0.4 15 11 DN20 M14×1.5 1350×1100×950
WWZ-30/4-150 30 0.4 15 15 DN20 M14×1.5 1450×1100×1000
WWZ-45/4-150 45 0.4 15 18.5 DN20 M14×1.5 1580×1200×1120
WWZ-50/4-150 50 0.4 15 18.5 DN20 M14×1.5 1680×1250×1220
WWZ-60/4-150 60 0.4 15 22 DN20 M14×1.5 1780×1300×1250

Recommend the another Oil free Diphragm Compressor

The diaphragm compressor booster is a special structure of the volume-type compressor with high compression ratio, good leak tightness, compressed gas without lubricating oil and other solid impurities contaminated features, So it’s suitable for high purity compression, rare, valuable, inflammable, explosive, toxic, harmful, corrosive, and high pressure gas.

Keepwin produced Helium compressor, Oxygen Compressor, Hydrogen Compressor, Nitrogen Compressor, Recovery H2 Gas compressor, Argon compressor, cylinder filling booster compressor, etc widely used in Petrochemicals, Fine ChemicalsPharmaceutical ChemicalsEnergy ChemicalsMachinery IndustryElectronics IndustryAgricultureAnimal Husbandry and Defense Industry, AstronomyAerospace, Medical and other fields.
.
Advantages of Diaphragm compressor:
1.  Oil-free compression due to the hermetic separation between gas and oil chamber.
2.  Abrasion-free compression due to static seals in the gas stream
3.  Automatic shutdown in case of a diaphragm failure prevents damage
4.  High Compression Ratios-Discharge pressure up to 1000bar (14500 psig).
5.  Contamination Free Compression
6.  Corrosion Resistance
7.  High Reliability

As a displacement compressor with special,diaphragm compressor is characterized by large compression ratio,good sealing performace,and that the compress air will not be polluted by lubricant or other solid impurities.Therefore diaphragm compressor is applicable to compress high-purity,rare and precious,flammable and explosive,toxic and hazardous,corrosive and high pressure gases.
Keepwin diaghragm compressors consist of 4 types that are Z,V,L and D type.The exhaust pressure ranges from 1.3 to 100 Mpa. The products are widely used in the industries of national defense,scientific research, petrochemical, nuclear power, parmaceutical, food-stuff and gas separation.

We offer a wide variety and types of diaphragm compressors. You can install these in many different scenarios. It is possible to install the compressors in hydrogen houses between and electrolyzer and a storage system, in businesses to support their needs such as ice cream companies for hydrogenation, at farmers where they use it to produce ammonia or as a fuel at the back of a wind farm or solar farm, and refineries to pressurise the hydrogen before it is being used to clean up the gas or oil. There are also many applications for our H2 gas compressors.

For instance, you can also use the diaphragm compressor in green hydrogen transport applications, energy storage solutions, grid balancing, food processing, and power station cooling. We pride ourselves at ensuring that as many applications of our compressor units use renewable electricity to pressure the hydrogen.

Each of our H2 compressor units is unique. It is built to your needs all with the latest innovations in hydrogen compression, safety, and operation. We offer different hydrogen flow and pressures all set to match your storage working pressure.

We can customize hydrogen into different types of storage systems at 150bar 200 bar, 350 bar (5000 psi), 450 bar, 500 bar, 700 bar (10,000 psi), 900 bar (13,000 psi).

Main technical data

Cylinder 
All the cylinders comprise upper plate, diaphragms, and cylinder body etc. The diaphragms are clamped between the cylinder cover and cylinder body. The cylinder cover and cylinder body each has a concave recess hollowed out in their contacting faces. The gas cylinder is formed between cylinder cover concave recess and diaphragms. Both suction valve and discharge valve are fitted on the upper plate. Among of them, the discharge valve is located on the center of the upper plate. The evenly located small oil holes are on the cylinder body to deliver the oil pressure inside the oil cylinder to the bottom of diaphragms (each diaphragm compressor’s cylinder has 3 piece diaphragm.) 

Pressure Regulating Valve 
The oil pressure of oil cylinder is regulated by the tension of the valve spring.In case the oil pressure is higher than the regulated value, turn the regulating bolt counter-clockwise to loosen the spring tension, but turn the regulating bolt clockwise to tighten the spring, when the oil pressure is lower than the regulated value. When the oil pressure meets the required value, the regulating bolt must be locked with a lock-nut. The oil pressure of the oil cylinder shall always be higher than the discharge pressure by 15~20%. But the oil and gas differential pressure shall not be lower than 0.3MPa or higher than 1.5MPa. 

Cooler
The cooler structure is the double-wall pipe type. The circular space between the outer and inner pipe is the cooling water passage and the inner pipe is the gas passage. Normally the water inlet port is at the lower side and the water outlet port is at the upper side. The flow direction of cooling water and gas is on the contrary.

Oil Pressure Measuring Device 
The measuring device of oil cylinder discharge pressure consists of shock-proof pressure gauge, check valve and unloading valve. The case of the pressure gauge is totally airproof and filled with damping liquid. The inner devices of gauge is immersed in the liquid, which makes the pressure gauge hands stable through the function of the viscosity of damping liquid. The unloading valve is fitted under the gauge to discharge the remained air in the oil pipeline   and to unload the oil pressure gauge. Also the check valve connecting with oil cylinder through pipeline is fitted under the unloading valve.   

Oil pipes 
Oil pipes consist of lube oil pipe and oil pressure secure system.

The lubrication for the driving device adopts gear oil pump circulation pressure lubricating. The lube oil stored in the frame oil tank enters into the gear oil pump after being filtered and is pressed into the oil holes in the crankshaft through the gear oil pump to lubricate the crankshaft friction surface. At the same time, part of the lube oil reaches the crosshead pin and crosshead along the oil holes in the connecting rod to lubricate the friction surface. The oil pressure of gear oil pump shall be kept between 0.3~0.5Mpa, and the bearings at the 2 ends of crankshaft is splash lubricated. 
Oil pressure secure system consists of oil compensating pipe, pressure-measuring pipe and oil return pipe. The oil output from the oil compensating pump will supplement oil for compressor cylinders through the oil compensating pipe and the excess oil returns to the crankcase through the pressure-regulating valve.

FAQ
Q1: What’s your delivery time?
A: Generally 5-10 days if the goods are in stock. Or it is 20-35 days if the goods are not in stock, it is according to quantity.

Q2: How long is your air compressor warranty?
A: Usually 1 year /12 Months for whole compressor machine, 2years/24months for air end (except maintenance spare parts.). And we can provide further warranty if necessary. 

Q3: How long could your air compressor be used?
A: Generally, more than 10 years.

Q4: Can you do OEM for us?
A: Yes, of course. We have around 2 decades OEM experience.And also we can do ODM for you.

Q5: What’s payment term?
A: T/T, L/C, D/P, Western Union, Paypal, Credit Card, Trade Assurance and etc. Also we could accept USD, RMB, GBP, Euro and other currency.

Q6: How about your customer service?
A: 24 hours on-line service available. 48hours problem sovled promise.

Q7: How about your after-sales service?
A: 1. Provide customers with intallation and commissioning online instructions.
2. Well-trained engineers available to overseas after-sales service. 

Q8. Are you factory?
A4: Absolutely! You have touched the primary sources of Air /Gas Compressor. We are factory.

How to contact with us?
Send your Inquiry Details in the Below, or Click “Send inquiry to supplier” to check more other Gas Compressor machine equipment!

 

Choosing the Right Air Compressor For Your Home

You will find that air compressors are indispensable tools for a variety of situations, including garages, home workshops, and basements. These tools can power a variety of tools, and each model is sized to suit the job at hand. Because air compressors have only 1 motor, they are lightweight, compact, and easy to handle. Using 1 air compressor to power several tools will also reduce the wear and tear on individual components. This article will introduce some important characteristics to look for when choosing the right air compressor for your home.

Positive displacement

A positive displacement compressor applies pressure to a fluid, whereas a centrifugal 1 does the opposite. A positive displacement compressor creates the desired pressure by trapping air and increasing its volume. Its discharge valve releases the high-pressure gas. These compressors are used in industrial applications and nuclear power plants. The difference between a positive and negative displacement compressor is that a positive displacement compressor can compress and release air at a consistent rate.
A positive displacement air compressor uses a reciprocating piston to compress air. This reduces the volume of the air in the compression chamber, and a discharge valve opens when the pressure reaches the desired level. These compressors are used in bicycle pumps and other pneumatic tools. Positive displacement air compressors have multiple inlet ports and have several configurations. Positive displacement air compressors have a single-acting and double-acting piston, and can be oil-lubricated or oil-free.
A positive displacement air compressor is different from a dynamic compressor. It draws air into the compression chambers and then releases the pressure when the valve is opened. Positive displacement compressors are common in industrial applications and are available in single-acting, double-acting, and oil-lubricated models. Large piston compressors have ventilated intermediate pieces and crossheads on gudgeon pins. Smaller models have permanently sealed crankcases with bearings.
air-compressor

Oil-free

Oil-free air compressors have some advantages over their oil-lubricated counterparts. They do not require lubrication oil because they are coated with Teflon. The material has 1 of the lowest coefficients of friction and is layered, so it slides past other layers with little effort. Because of this, oil-free compressors tend to be cheaper and still deliver comparable performance. Oil-free compressors are a good choice for industrial applications.
The life of an oil-free air compressor is significantly longer than an oil-lubricated counterpart. These models can operate up to 2,000 hours, 4 times longer than the average oil-lubed compressor. Oil-free compressors also have a significantly lower operating noise than their oil-lubricated counterparts. And because they don’t need oil changes, they are quieter. Some even last up to 2,000 hours.
An oil-free air compressor is a good choice if your application requires high levels of purity. Several applications require ultra-pure air, and even a drop of oil can cause product spoilage or damage to production equipment. In addition to the health risks, an oil-free air compressor reduces the costs associated with oil contamination and minimizes leaks. It also eliminates the need for oil collection, disposal, and treatment.
A typical oil-free air compressor is very efficient, requiring only about 18% of the full load horsepower. However, oil-free compressors have a higher risk of premature failure and are not recommended for large-scale industrial applications. They may also use up to 18% of the compressor’s full capacity. They may sound appealing, but you must make sure you understand the benefits of an oil-free air compressor before choosing 1 for your industrial applications.

Single-stage

A single-stage air compressor is designed to provide the power for a single pneumatic tool or device. These machines are generally smaller than two-stage compressors and produce less heat and energy. These machines aren’t designed for heavy-duty industries, but they are still highly effective for a variety of applications, including auto shops, gas stations, and various manufacturing plants. They can also be used in borewells, as they are suitable for small spaces with low air flow requirements.
A single-stage air compressor has 1 cylinder and 2 valves – the inlet and the delivery valves. Both of these valves function mechanically, with the inlet valve controlling torque and the delivery 1 controlling air pressure. Generally, single-stage compressors are powered by a gas engine, but there are also electric models available. The single-stage air compressor is the most common type of air compressor. It has a single cylinder, 1 piston, and 1 air cylinder.
The single-stage air compressors are used for small projects or personal use. A two-stage air compressor is more effective for industrial projects. Its longer air end life makes it more efficient. It is also more efficient for use in the automotive industry, where the engine has many cylinders. In general, single-stage compressors require a higher power level. The single-stage model is ideal for small projects, while a two-stage 1 is suitable for larger-scale arsenals.
air-compressor

CFM

The cubic foot-per-minute (CFM) of an air compressor is the output of the machine. In order to calculate the CFM level, start by looking at the compressor’s specifications. You should know how many cubic feet the unit can hold and how many pounds per square inch it can compress. Once you have these information, you can calculate the CFM. Now you can use these numbers to select an appropriate air compressor for your needs.
The most common way to increase the CFM of an air compressor is to turn the regulator down. By turning the dial down, the air compressor will produce more than 10 CFM. You can also try connecting 2 output valves. Make sure that the settings are adjusted properly before you begin. This will ensure that your air compressor is functioning at its maximum efficiency and lifespan. To increase the CFM of your air compressor, first check that your regulator is calibrated for the desired pressure level.
To calculate the CFM of an air compressor, first determine the tank volume of the machine. Then, multiply this volume by the time it takes to fill the tank. Then, divide the result by 60 seconds to calculate the CFM. Once you know how much air your machine can hold, you can choose a suitable air compressor. If you’re working in a confined area, you should buy a tool with a large tank.

PSI

The PSI of an air compressor is the pressure that it can output. A typical air compressor has a gauge connected to the airline at the bottom, next to it, or between the two. The gauge tells the actual pressure of the air compressor, while the cut-out pressure is determined by the manufacturer. The manufacturer recommends that you set the cut-out pressure 20 to 40 PSI higher than the factory recommended pressure. If you want to set the pressure for your nail gun, you can use the cut-in and cut-out pressures on your compressor, and the tank won’t exceed this range.
The PSI of an air compressor measures the force that it can deliver, which is often in pounds per square inch. For most air tools, you need at least 40 to 90 psi. In general, reciprocating air compressors work on an on/off basis. This relationship is known as the duty cycle. All air compressors are rated for a particular duty cycle, such as 50 percent on and 20-5 percent off.
The Psig of an air compressor is not free, as many people believe. The PSI of an air compressor is not free, but it is essential to maintain it for safe operations. If you’re having trouble maintaining a consistent pressure, consider turning down the PSI of your compressor by 2 psig. This will determine the critical pressure for the machine. You’ll also increase the amount of energy in the system by 1 percent.
air-compressor

Power source

The power source for an air compressor is crucial in its operation. Without the correct voltage and amperage, air compressors will not function properly. The power source must be close to the compressor so that it can plug into an electrical outlet. If it is too far from the outlet, the compressor may not be able to build enough pressure. When this happens, the fuse inside the air compressor will turn off to protect the user. The power source should be a safe distance from the compressor.
Most manufacturers do not specify the power source for an air compressor. Depending on the horsepower, the compressor will require approximately 4 amps of power. A one-horsepower compressor would draw about 12 amps. If it were powered by a typical 120-volt household supply, its motor would exceed the 15-amp breaker capacity. A larger air compressor, however, will require a separate 15-amp power source, making it impossible to use it with this type of power source.
The power source for an air compressor is typically electrical alternating current (AC) that is equivalent to the voltage on a standard wall outlet. A three-phase air compressor, on the other hand, requires a special AC supply with 3 electrical offset pulses. Regardless of the type of air compressor, the power source must be compatible with the incoming power service. One of the most common problems when attempting to connect an air compressor to an AC power source is undersized wire. This results in low voltage and high amperes, tripping of over-load relays and blown fuses.

China Best Quality Anti-Acid Sulfur Hexafluoride Sf6 Gas Compressor Hydrogen Compressor Oil Free Piston Compressor  China Best Quality Anti-Acid Sulfur Hexafluoride Sf6 Gas Compressor Hydrogen Compressor Oil Free Piston Compressor

Co2 air compressor

As one of the co2 air compressor manufacturers, suppliers, and exporters of mechanical products, We offer co2 air compressors and many other products.

Please get in touch with us for details.

Manufacturer supplier exporter of co2 air compressor.

Recent Posts